MR2 FUSE BOX RELOCATION

Relocating Electronics into trunk | MR2 Owners Club Forum
I have my fuse box and ignitor in the trunk. It was alot of work extending parts or the harness and moving some things but really not to bad. Also the large loom that goes to the fuse box up to the front kick pannel I ran in the drivers air duct up over the wheel well and back into the trunk so its out of the engine bay.
Replace Battery Cables and Relocate Battery - mr2
Note: O’Reilly’s is a great place for cheap but quality cables are sold by the foot and are actually made of copper, instead of CCA (copper clad aluminum). Steps. 1. Put the car up on jack stands (we will need to access the starter and the bottom of the alternator later on). 2. Disconnect the battery — start with the negative side, then disconnect the positive side.
MR2 Owners Club - Parts Lists Various Conversions
- MR2 loom (to butcher to fit the speed sensor & connectors in fusebox) Misc: - 6 rib poly V belt - Either mk2 Turbo body loom including fuse box or wiring diagrams for both the NA and Turbo for pin relocation at ecu/fuse box Miscellaneous. - Mk2 Turbo fuel pump or Walbro unit - Mk2 Turbo engine mounts - Aftermarket air intake filter/cone
battery relocation.. | Page 2 | MR2 Owners Club Forum
in all honesty. you'll probably never blow that fuse. if it does blow, something went very wrong and it requires immediate attention. so no, skip the breaker. the fuse isnt even necessary for the system to work. you shouldnt ever *need* that fuse, its just a little protection for the worst..
Questions on relocating the fuse box. - Nissan Forum
Car: 1992 Toyota MR2 N/A, 1991 Toyota MR2 Turbo. Questions on relocating the fuse box. Quote; fixing to swap a RB25 into and i want the engine bay to be wire free as possible so im wanting to move the battery and fuse box to the Also I guess I'm going to try and price together a battery relocation kit.I can't see paying 100$ for a kit. Top.
Electrical – Dash and Running Lights Not Working – MR2
Check the No. 3 Junction Box: There is a junction box in the corner of the driver’s side foot-well to the left of the clutch pedal. Try unplugging the connector for the dash lights and then re-connecting it. Junction Box No 3 – Location Under Dash Junction Box No 3 Junction Box No 3 – Dash Light Plug Removed
Battery relocation to frunk [Archive] - Toyota MR2 Message
I am interested in putting my battery in the frunk of my mk1 I read somewhere the easiest way is to get a mk2 battery cable as it will be the perfect size, so i have already got one of those i found some info here: Technical Garage - Technical Garage - AW11 MR2 Battery Relocation this guy put in a 150 amp fuse, is this really necessary ?
Search Results - Toyota MR2 Message Board
Toyota MR2 Message Board and Forum for Toyota MR2 Owners and Enthusiasts. A Place to Learn About One of the Best Sports Cars Ever Made, the Toyota MR2. Click to Enter the Toyota MR2
20V Blacktop Swap - Wiring - Midship Runabout
I also removed the body harness from the MR2, which made it easier to trace wires back into the fuse box (the engine fuse box is on the body harness of the MR2, engine harness of the 20V). I also needed to run more wires to the MR2s body harness for the Blacktop, more on that later. No need to label every connector on the MR2.
In-hood Fuse/Relay Relocation (simple) - Nissan Forum
I didn't read in *detail* the wires you extended, but worth noting: the point of the fuse box in the 'bay is to protect lengths of wires from shorts. You fuse as close to possible to the source. Extending wires upstream of the fuse is asking for melted wires. Good